This is an excellent screen filter for the Sony PSP. It reduces the glare on the screen, it's scratch resistant and doesn't show finger prints as easily as the PSP screen. The instructions aren't 100% clear and I can see how this product has gotten some negative reviews on other sites.
In essence it's a clear plastic layer that you place down with a sticky substance on your PSP screen. You need to clean your screen VERY well to start with. We have eyeglass cleaner in the house and it worked perfectly - not a speck of dust or lint was left when we began.
Then we carefully followed their instructions to lay down the screen. It went down without any problem at all, and was crystal clear once it was down. Playing through it did not present any issue, and it really does a good job of keeping oils and dust away from the actual screen surface.
This PSP accessory was easy to use, the specification was helpful, and the screen is just as clear as before with fewer glares. I tried a couple of the cheaper screen protectors you can pick up anywhere, and they all left much to be desired. I came across a review for one of these and it looked better than the others so I ordered one. I'm glad I did. The Hori filter is easily the best one I have ever seen. Don't be fooled by cheap alternatives, Hori is the best and worth the pricey price and shipping. I highly recommend the product to anyone looking to protect their investment. It is a small price relative to an irremovable scratch across the screen. Take this one as an example, this is a typical kind of PSP accessories---- Protective Filter, much lower price and high quality, move to visit geartaker.com and take it home right now!
Many people have problem applying the filter. If you just peel off and apply the sticker directly, you will face the following 3 major problem:
1. Dust particles
2. air bubbles (or known as air pockets, caused by air or dust)
3. Sticker orientation accuracy
To solve the above problems, here is the secret and the correct steps, not limited to this PSP filter, in fact, this secret applied to all stickers application.
Do the following steps, and you will be amazed with the result.
Ingredients:
a. The screen protector filter
b. Bowl
c. hand soap, body shampoo (lotion, etc.. anything alcaline based will do)
d. water
e. plastic paper credit card sized or smaller which act as your lifter. Optional, use the front/back plastic cover for the sticker will do as well.
f. tissue paper
Steps
1. Wipe the PSP screen clean
2. Fill the bowl with one or two teaspoon amount of hand soap and dilute it with half bowl of water.
3. scoop out the bubbles in the bowl as many as possible.
4. Remove both front and back side of the filter. (remember the up-side)
5. Soak the filter into the bowl and take it out with your plastic paper. (try not to use finger)
6. Apply the filter gently (while it is still little wet)
7. Adjust the filter to the correct position desired.
8. Push the liquid out with a credit card from middle to outside.
9. Wipe any water that squeezed out from the corner of the sticker as soon as soon you see it.
10. If you see dust particle (a small air pocket with a little dust dot in the middle) inside the sticker, lift it up with a plaster paper, remove the dust, and close it back.
11. repeat step 7 to 10 until it is completely dry and up to your desire.
Many people have problem applying the filter. If you just peel off and apply the sticker directly, you will face the following 3 major problem:
1. Dust particles
2. air bubbles (or known as air pockets, caused by air or dust)
3. Sticker orientation accuracy
To solve the above problems, here is the secret and the correct steps, not limited to this PSP filter, in fact, this secret applied to all stickers application.
Do the following steps, and you will be amazed with the result.
Ingredients:
a. The screen protector filter
b. Bowl
c. hand soap, body shampoo (lotion, etc.. anything alcaline based will do)
d. water
e. plastic paper credit card sized or smaller which act as your lifter. Optional, use the front/back plastic cover for the sticker will do as well.
f. tissue paper
Steps
1. Wipe the PSP screen clean
2. Fill the bowl with one or two teaspoon amount of hand soap and dilute it with half bowl of water.
3. scoop out the bubbles in the bowl as many as possible.
4. Remove both front and back side of the filter. (remember the up-side)
5. Soak the filter into the bowl and take it out with your plastic paper. (try not to use finger)
6. Apply the filter gently (while it is still little wet)
7. Adjust the filter to the correct position desired.
8. Push the liquid out with a credit card from middle to outside.
9. Wipe any water that squeezed out from the corner of the sticker as soon as soon you see it.
10. If you see dust particle (a small air pocket with a little dust dot in the middle) inside the sticker, lift it up with a plaster paper, remove the dust, and close it back.
11. repeat step 7 to 10 until it is completely dry and up to your desire.
Geartaker.com offers high-quality products at extremely lower price. I high recommend this site, for I bought many PSP accessories from Geartaker, the service made me feel so comfortable, Geartaker must be my very first option if I want online shopping.
Other Related Arcles
没有评论:
发表评论